View all videos : shorturl.at/bwL37
what is wood carving ?
Wood carving is a form of woodworking by means of a cutting tool (knife) in one hand or a chisel by two hands or with one hand on a chisel and one hand on a mallet, resulting in a wooden figure or figurine, or in the sculptural ornamentation of a wooden object.
Wood carving process
Selection
The nature of the wood being carved limits the scope of the carver in that wood is not equally strong in all directions: it is an anisotropic material. The direction in which wood is strongest is called "grain" (grain may be straight, interlocked, wavy or fiddleback, etc.). It is smart to arrange the more delicate parts of a design along the grain instead of across it. Often, however, a "line of best fit" is instead employed, since a design may have multiple weak points in different directions, or orientation of these along the grain would necessitate carving detail on end grain, (which is considerably more difficult). Carving blanks are also sometimes assembled, as with carousel horses, out of many smaller boards, and in this way, one can orient different areas of a carving in the most logical way, both for the carving process and for durability. Less commonly, this same principle is used in solid pieces of wood, where the fork of two branches is utilized for its divergent grain, or a branch off of a larger log is carved into a beak (this was the technique employed for traditional Welsh shepherd's crooks, and some Native American adze handles). The failure to appreciate these primary rules may constantly be seen in damaged work, when it will be noticed that, whereas tendrils, tips of birds beaks, etc., arranged across the grain have been broken away, similar details designed more in harmony with the growth of the wood and not too deeply undercut remain intact.
Probably the two most common woods used for carving in North America are basswood (aka tilia or lime) and tupelo; both are hardwoods that are relatively easy to work with. Chestnut, butternut, oak, American walnut, mahogany and teak are also very good woods; while for fine work Italian walnut, sycamore maple, apple, pear, box or plum, are usually chosen. Decoration that is to be painted and of not too delicate a nature is often carved in pine, which is relatively soft and inexpensive.
Sculpture
A wood carver begins a new carving by selecting a chunk of wood the approximate size and shape of the figure he or she wishes to create or if the carving is to be large, several pieces of wood may be laminated together to create the required size. The type of wood is important. Hardwoods are more difficult to shape but have greater luster and longevity. Softer woods may be easier to carve but are more prone to damage. Any wood can be carved but they all have different qualities and characteristics. The choice will depend on the requirements of carving being done: for example, a detailed figure would need a wood with a fine grain and very little figure as a strong figure can interfere with 'reading' fine detail.
Once the sculptor has selected their wood, he or she begins a general shaping process using gouges of various sizes. The gouge is a curved blade that can remove large portions of wood smoothly. For harder woods, the sculptor may use gouges sharpened with stronger bevels, about 35 degrees, and a mallet similar to a stone carver's. The terms gouge and chisel are open to confusion. Correctly, a gouge is a tool with a curved cross-section and a chisel is a tool with a flat cross-section. However, professional carvers tend to refer to them all as 'chisels'. Smaller sculptures may require the woodcarver to use a knife, and larger pieces might require the use of a saw. No matter what wood is selected or tool used, the wood sculptor must always carve either across or with the grain of the wood, never against the grain.
Once the general shape is made, the carver may use a variety of tools for creating details. For example, a “veiner” or “fluter” can be used to make deep gouges into the surface, or a “v-tool” for making fine lines or decorative cuts. Once the finer details have been added, the woodcarver finishes the surface. The method chosen depends on the required quality of the surface finish. The texture left by shallow gouges gives 'life' to the carving's surface and many carvers prefer this 'tooled' finish. If a completely smooth surface is required general smoothing can be done with tools such as “rasps,” which are flat-bladed tools with a surface of pointed teeth. “Rifflers” are similar to rasps, but smaller, usually double-ended, and of various shapes for working in folds or crevasses. The finer polishing is done with abrasive paper. Large grained paper with a rougher surface is used first, with the sculptor then using finer grained paper that can make the surface of the sculpture slick to the touch.
#Wood #wood_carving #Bedside_table